Overview
The ZF 0630.501.213 RETAINING RING is a critical axial locking component engineered specifically for the WG160 series and its heavy-duty derivatives. This OEM genuine part secures internal gear assemblies and bearing packs within the transmission housing, preventing unwanted lateral movement during high-torque operation. The SKU 0630.501.213 is precision-machined to maintain exacting clearance tolerances, ensuring that the planetary gear sets remain properly seated against the 4656101037: TRANSMISSION HOUSING and adjacent structural components. Without this ring, the entire rotating assembly can shift under load, leading to rapid wear and catastrophic failure.
Symptoms of Failure
- Axial gear clatter under load: A distinct knocking or ticking sound from the transmission bell housing, especially during acceleration or deceleration, indicates the retaining ring has lost its grip.
- Unexplained oil leaks at the front section: When the ring fails, the 4656201075: HOUS.FRONT SECT can shift, breaking the seal and causing fluid to weep from the mating face.
- Intermittent gear slipping in higher ranges: A worn retaining ring allows the sun gear shaft to drift, causing momentary loss of drive in WG160 and WG190 transmissions.
- Metal debris in the oil pan: Fretting wear from a loose ring generates fine metallic particles, often found during routine oil changes.
Technical Specifications
| Parameter | Value |
|---|---|
| Part Number (SKU) | 0630.501.213 |
| Material | Spring steel (C67S), phosphate coated |
| Inner Diameter (nominal) | 130.0 mm |
| Cross-section thickness | 4.0 mm |
| Weight | 0.045 kg |
| OEM Reference | ZF 0630.501.213 |
| Installation torque (adjacent fasteners) | Refer to 0636100817: CAP SCREW spec |
Compatibility
This retaining ring is a shared service part across the ZF WG series modular platform. It is confirmed for use in the WG160, WG190, WG191, WG210, WG211, and WG230 transmission families. In each application, it seats inside the 4656201035: HOUSING REAR PART or the 4472239178: HOUSING REAR PART, depending on the generation. Always verify the groove condition in the housing before installation.
Related Components
| Part Number | Name | Function |
|---|---|---|
| 4656101037 | TRANSMISSION HOUSING | Main structural casing for gear train |
| 4656201075 | HOUS.FRONT SECT | Front bell housing section |
| 4656201035 | HOUSING REAR PART | Rear adapter housing |
| 4472239178 | HOUSING REAR PART | Alternate rear housing variant |
| 0631306816 | CYLINDRICAL PIN | Alignment dowel for housing halves |
| 4656301148 | FIXING PLATE | Locks retaining ring in groove |
| 0636100817 | CAP SCREW | M10 fastener for fixing plate |
| 4656301016 | SCREEN SHEET | Fine mesh oil strainer (short) |
| 4656301017 | SCREEN SHEET | Fine mesh oil strainer (long) |
| 0636100803 | CAP SCREW | M8 fastener for screen sheet |
Frequently Asked Questions
Q: Can I reuse the 0630.501.213 retaining ring after disassembly?
A: No. This is a single-use spring steel ring. Reusing it risks loss of tension, leading to the failure symptoms described above. Always install a new OEM ring.
Q: Does this ring fit the WG180 or WG200 transmissions?
A: The WG180 and WG200 use a different groove diameter. This specific SKU is designed for the WG160 through WG230 series only. Consult the housing part number to confirm compatibility.
Q: What tool is required to install this retaining ring?
A: Use internal snap-ring pliers with 90-degree tips. Ensure the ring is fully seated in the groove of the housing before installing the fixing plate.
📞 Need this part? Contact our ZF specialists:
Email: info@partszf.com |
Phone: +86 158 2286 3467 |
Request a Quote →
