Overview
The ZF 2093.110.006 P.T.O. SHAFT is a critical power take-off component engineered for the WG100, WG130, and WG131 transmission series. This OEM genuine part transfers rotational energy from the transmission gear train to auxiliary hydraulic pumps or driven equipment. Positioned within the lower gear cluster, the shaft interfaces directly with the 2093109001: DIFFERENTIAL assembly to ensure synchronized torque delivery. The SKU 2093.110.006 is precision-machined to maintain concentricity under high-load conditions, preventing vibration that could compromise adjacent driveline components.
Symptoms of Failure
- Intermittent PTO engagement failure – Worn splines on the 2093.110.006 shaft cause the clutch collar to skip, resulting in partial or complete loss of auxiliary power during operation.
- Metallic grinding noise from transmission housing – Excessive play between the shaft and the 2093309071: DIFF.HOUSING produces a distinct chatter at idle or under load.
- Hydraulic pump output fluctuation – A fatigued shaft twists slightly under torque, causing irregular pump speed and pressure drops in attached systems.
- Oil seepage near the PTO mounting flange – Cracks or pitting on the shaft surface degrade the seal contact area, allowing transmission fluid to escape.
Technical Specifications
| Parameter | Value |
|---|---|
| Part Number | 2093.110.006 |
| Overall Length | 245 mm |
| Spline Diameter | 32 mm (10-spline) |
| Material | Case-hardened alloy steel (20MnCr5) |
| Weight | 1.85 kg |
| OEM Reference | ZF 2093.110.006 |
| Surface Treatment | Black oxide + phosphate coating |
| Hardness | 58-62 HRC (core) |
Compatibility
This P.T.O. shaft is validated for use in ZF WG100, WG130, and WG131 transmissions. It also fits select WG180 and WG200 variants when paired with the correct 0750117075: TAPER ROLLER BEARING and 2093209095: DIFFERENTIAL assembly. Always verify the spline count and shaft shoulder height against your transmission’s service manual before installation.
Related Components
| Part Number | Name | Function |
|---|---|---|
| 2093109001 | DIFFERENTIAL | Distributes torque between drive axles |
| 0750117075 | TAPER ROLLER BEARING | Supports radial and axial shaft loads |
| 2093209095 | DIFFERENTIAL | Secondary torque split unit |
| 2093309071 | DIFF.HOUSING | Encloses differential gears and bearings |
| 0631100223 | SPRING PIN | Secures shaft to gear hub |
| 0730300820 | THRUST WASHER | Controls axial clearance in gear stack |
| 4482360002 | AXLE BEVEL GEAR | Transfers power to wheel ends |
| 2097309085 | DIFFERENTIAL AXLE | Carries differential side gears |
| 5838300811 | THRUST WASHER | Reduces friction on differential pinion |
| 4482360001 | DIFFERENTIAL BEVEL GEAR | Mesh with axle bevel gear for rotation |
Frequently Asked Questions
Q: Can the 2093.110.006 shaft be used in a WG180 transmission without modification?
A: The shaft is dimensionally compatible with WG180 units, but you must install the correct 0750117075: TAPER ROLLER BEARING to match the larger housing bore. Always measure the spline engagement depth before final assembly.
Q: How do I confirm the shaft is not bent before installation?
A: Place the shaft on V-blocks and rotate it with a dial indicator. Runout should not exceed 0.05 mm. Any deviation above this threshold indicates fatigue and requires replacement.
Q: What torque specification applies to the retaining nut on this PTO shaft?
A: ZF recommends 180 N·m for the locknut, applied with thread-locking compound. Re-torque after 50 operating hours to account for initial seating of the 2093309071: DIFF.HOUSING interface.
📞 Need this part? Contact our ZF specialists:
Email: info@partszf.com |
Phone: +86 158 2286 3467 |
Request a Quote →
ZF 2093.110.006 P.T.O. SHAFT – Shaft RFQ Support
PartsZF supports RFQ preparation for ZF 2093.110.006 P.T.O. SHAFT where shaft identification and documentation review are required before ordering.
Part-Number Summary
Use ZF number 2093.110.006 when sending your RFQ. PartsZF can review dotted, spaced, and compact number formats against the available product and documentation records.
Application Context
- Illustration section: P.T.O. SHAFT
Cross Reference Support
If you have an OEM number, old supplier number, or visible marking, include it with your RFQ so PartsZF can compare it with the available records.
Specification Snapshot
| ZF part number | 2093.110.006 |
|---|---|
| Normalized SKU | 2093110006 |
| Part name | P.T.O. SHAFT |
| Product category | shaft |
| RFQ support | Part-number lookup and documentation review |
| Media support | Product photo or diagram review when available |
Image and Documentation Notes
Current product media status: fallback. Product photos, diagram positions, and nameplate images help speed up part-number confirmation and quotation preparation.
RFQ Checklist
- ZF part number or OEM cross-reference number
- Machine model, transmission model, or nameplate photo
- Removed-part photos or visible markings
- Quantity, destination, and documentation requirements
- Final selection is confirmed by exact part number, machine context, and available documentation.
Related Parts
- ZF 2094.110.011 P.T.O. SHAFT
- ZF 2094.110.014 P.T.O. SHAFT
- ZF 4642.303.002 OUTPUT SHAFT
- ZF 2093.110.011 P.T.O. SHAFT
- ZF 5838.300.106 INPUT SHAFT
