Overview
The ZF 6057.018.213 CONTROL UNIT is a critical electro-hydraulic interface module specifically engineered for the WG 210 Series transmission family. This OEM genuine part governs shift timing, pressure modulation, and torque converter lock-up within the valve body assembly. Positioned directly on the main control housing, it interprets electronic signals from the vehicle’s ECU and converts them into precise hydraulic actions. The SKU 6057.018.213 ensures direct plug-and-play compatibility with existing harnesses and mounting points, eliminating the need for adapter plates or software recalibration. When paired with a robust TRANSMISSION HOUSING, this control unit maintains consistent line pressure across all operating temperatures.
Symptoms of Failure
- Erratic shift patterns and delayed engagement: A worn 6057.018.213 often causes harsh upshifts or slipping between gears, especially under load. This is frequently searched as “ZF WG210 shifting problems” or “transmission control unit failure symptoms.”
- Intermittent loss of reverse gear: When the control unit’s solenoid driver circuits degrade, reverse engagement may become sluggish or fail entirely. Technicians often report this as “WG210 no reverse” or “control unit electrical fault.”
- Torque converter shudder at highway speeds: A failing unit disrupts lock-up clutch modulation, producing a vibration during steady cruising. This aligns with long-tail queries like “ZF transmission shudder fix” or “control unit torque converter slip.”
- Persistent transmission warning light with stored fault codes: The unit may trigger P0700 or P0741 codes due to internal short circuits or degraded pressure regulation, even when fluid levels are correct.
Technical Specifications
| Parameter | Value |
|---|---|
| Part Number | 6057.018.213 |
| OEM Reference | ZF 6057 018 213 |
| Material | Die-cast aluminum housing with glass-filled nylon solenoid body |
| Weight | 1.85 kg (4.08 lbs) |
| Dimensions (L x W x H) | 210 mm x 140 mm x 65 mm |
| Operating Voltage | 12V DC (24V compatible with resistor harness) |
| Seal Type | Integrated O-ring gasket (pre-installed) |
Compatibility
This control unit is primarily designed for the ZF WG210 series, but it also retrofits into the WG180, WG200, and WG250 models when used with the correct valve body spacer plate. It is a direct replacement for earlier part numbers 6057.018.210 and 6057.018.211. For complete assembly integrity, always inspect the HOUS.FRONT SECT and HOUSING REAR PART for cracks or warping before installation. In heavy-duty applications, the HOUSING REAR SECTION must be torqued to factory specifications to prevent fluid cross-leakage.
Related Components
| Part Number | Name | Function |
|---|---|---|
| 4657101078 | TRANSMISSION HOUSING | Main structural casing for gear sets and valve body |
| 4657201166 | HOUS.FRONT SECT | Front section housing torque converter and pump |
| 4657201168 | HOUSING REAR PART | Rear casing supporting output shaft and PTO mount |
| 4657298101 | HOUSING REAR SECTION | Extended rear section for auxiliary drive interfaces |
| 0631306816 | CYLINDRICAL PIN | Alignment dowel for control unit positioning |
| 0636100801 | CAP SCREW | M8 fastening bolt for control unit mounting |
| 4656301148 | FIXING PLATE | Retention bracket for solenoid harness |
| 4657301032 | SCREEN SHEET | Fine mesh filter for valve body inlet |
| 4657301033 | SCREEN SHEET | Secondary filter for control unit return line |
| 0636100803 | CAP SCREW | M10 bolt for housing section fastening |
Frequently Asked Questions
Q: Can the 6057.018.213 be repaired, or must it be replaced?
A: This unit is a sealed assembly with non-serviceable internal solenoids and circuit boards. ZF does not offer repair kits; replacement with the OEM genuine part is the only reliable solution to restore proper shift quality.
Q: Does this control unit require programming after installation?
A: No. The 6057.018.213 is a passive control unit that receives commands from the transmission ECU. No flash programming or adaptation reset is needed, though a battery disconnect cycle is recommended to clear stored fault codes.
Q: What torque specification should be used for the mounting cap screws?
A: Use 12 Nm (106 in-lbs) for the M8 cap screws (part 0636100801) and 25 Nm (221 in-lbs) for the M10 cap screws (part 0636100803). Over-tightening can crack the control unit housing.
📞 Need this part? Contact our ZF specialists:
Email: info@partszf.com |
Phone: +86 158 2286 3467 |
Request a Quote →
ZF 6057.018.213 CONTROL UNIT – Control Unit RFQ Support
PartsZF helps B2B buyers source ZF 6057.018.213 CONTROL UNIT with fast RFQ support, expert part-number lookup, documentation review, and export coordination. This control unit page is built from confirmed catalog, media, and reference data to reduce sourcing uncertainty for construction machinery transmission parts.
Part-Number Summary
Use ZF number 6057.018.213 when sending your RFQ. PartsZF can review dotted, spaced, and compact number formats against the available product and documentation records.
Application Context
- Documentation reference: 4657054158
- Documentation reference available for RFQ review
- Illustration section: LOOSE PARTS
Cross Reference Support
If you have an OEM number, old supplier number, or visible marking, include it with your RFQ so PartsZF can compare it with the available records.
Specification Snapshot
| ZF part number | 6057.018.213 |
|---|---|
| Normalized SKU | 6057018213 |
| Part name | CONTROL UNIT |
| Product category | control unit |
| Cross-reference support | Available for RFQ review |
Image and Documentation Notes
Current product media status: fallback. Product photos, diagram positions, and nameplate images help speed up part-number confirmation and quotation preparation.
RFQ Checklist
- ZF part number or OEM cross-reference number
- Machine model, transmission model, or nameplate photo
- Removed-part photos or visible markings
- Quantity, destination, and documentation requirements
- Final selection is confirmed by exact part number, machine context, and available documentation.
Related Parts
- ZF 4646.123.009 CONTROL UNIT
- ZF 4646.123.011 CONTROL UNIT
- ZF 4646.164.005 CONTROL UNIT
- ZF 4646.164.404 CONTROL UNIT
- ZF 6009.092.276 CONTROL UNIT
